CSSD Systems

WS 3102 wash stations with 2 sinks for dirty area

Size (L x W x H): 2000x750x850 mm
The worktop is made of solid, bright-polished minimum sheet thickness of 1.5 mm stainless steel (304) to withstand heavy-duty work with wet instrument.
It is designed with an integrated 10 mm high edge at the front and sides, and a 60 mm high edge (splash back) at the rear
The front and side edges are reinforced and widened to 49 mm. Edges are welded together and polished at the corners.
The worktop slopes to the sink, and reinforced by a full-length support frame.
The support frame is a complete assembly with the front, back and ends welded together at the corners.
The worktop and support frame is bonded together with double-adhesive tape of a special, age-resistant quality to give rigidity and noise abatement.
The floor stand is made of polished stainless steel.
The table is available with double sink units at both ends of the table, all with a smooth, polished inside finish made of stainless steel (304) top
Corners are curved to a 65 mm radius for easy cleaning.
The bottom has slope to the drain.
Sink units are 650 mm wide and 900 mm high (adjustable ± 25 mm) to accommodate large modular instrument trays
The legs provide strong support and hold to the entire unit securely.
The sink include a drain valve, removable strainer, manually operated drain-valve, overflow drainpipe and water trap. The table also includes a mixing faucet with swivel spout, for cold and hot water connection.

WT 3012 work table for wet goods for dirty area

Size (L x W x H): 2000x750x850 mm
The worktop is made of solid, bright-polished minimum sheet thickness of 1.5 mm stainless steel (304) to withstand heavy-duty work with wet instrument.
It is designed with an integrated 10 mm high edge at the front and sides, and a 60 mm high edge (splash back) at the rear
The front and side edges are reinforced and widened to 49 mm. Edges are welded together and polished at the corners.
The worktop slopes to the sink, and reinforced by a full-length support frame.
The support frame is a complete assembly with the front, back and ends welded together at the corners.
The worktop and support frame is bonded together with double-adhesive tape of a special, age-resistant quality to give rigidity and noise abatement.
The floor stand is made of polished stainless steel.
The table is available with double sink units at both ends of the table, all with a smooth, polished inside finish made of stainless steel (304) top
Corners are curved to a 65 mm radius for easy cleaning.
The bottom has slope to the drain.
Sink units are 650 mm wide and 900 mm high (adjustable ± 25 mm) to accommodate large modular instrument trays
The legs provide strong support and hold to the entire unit securely.
The sink include a drain valve, removable strainer, manually operated drain-valve, overflow drainpipe and water trap. The table also includes a mixing faucet with swivel spout, for cold and hot water connection.

WT 3013 work table for dry goods for clean area (Pass box receiving)

Size approx. (LxWxH):1800x650x900 mm
Stainless steel tables specially designed for working with dry goods and for general purpose pre storage.
The work tables have a rigid stainless steel construction which is easy to clean and without sharp edges or corners.
The table is ergonomically worked up, and have easy to clean robust mat finished (to reduce reflection of light from the surface) with minimum sheet thickness of 1.5 mm stainless steel (304) worktop/surface to withstand and carry out heavy work comfortably, either sitting or standing
The edges along the front, back and sides should be reinforced and widened to 37 mm, giving a rigid construction.
They are welded together and polished at all corners for good hygiene, as well as for the comfort and safety of the staff.
The worktop is supported by a complete assembly with full-length reinforcements along the front, back and ends, welded together at the corners.
The worktop and support frame are bonded together with double-adhesive tape of a special, age resistant quality to give rigidity and noise abatement.
The support frame has to be mounted on a solid, stable floor stand, made of polished stainless steel square tubing, with horizontal braces 300 mm above floor level. An adjustable10 cm (± 25 mm) plastic foot, easy to clean, is mounted on each leg
The provision is to be made for a sturdy 445 mm-wide stainless steel shelf (optional) can be mounted on the horizontal braces.
All edges are smooth and the rigid frame are made up of minimum 1.5 mm sheet thickness stainless steel (304).
There is unobstructed access to the working space, since the only supports needed along the front of the table are the corner legs. This also facilitates cleaning of floors.

WT 3015 work table for dry goods for sterile area

Size (LxWxH) :1800x650x900 mm
Stainless steel tables specially designed for working with dry goods and for general purpose prestorage.
The table is ergonomically worked up, should have easy to clean robust mat finished (to reduce reflection of light from the surface) with minimum sheet thickness of 1.5 mm stainless steel (304) worktop/surface to withstand and carry out heavy work comfortably, either sitting or standing.
The edges along the front, back and sides are reinforced and widened to 37 mm, giving a rigid construction.
They are welded together and polished at all corners for good hygiene, as well as for the comfort and safety of the staff.
The worktop is supported by a complete assembly with full-length reinforcements along the front, back and ends, welded together at the corners.
The worktop and support frame are bonded together with double-adhesive tape of a special, age resistant quality to give rigidity and noise abatement.
The support frame has to be mounted on a solid, stable floor stand, made of polished stainless steel square tubing, with horizontal braces 300 mm above floor level. An adjustable10 cm (± 25 mm) plastic foot, easy to clean, is mounted on each leg.
The provision is to be made for a sturdy 445 mm-wide stainless steel shelf (optional) can be mounted on the horizontal braces.
Must be delivered ready for assembly
All edges should be smooth and the rigid frame should be made up of minimum 1.5 mm sheet thickness stainless steel (304).
There is unobstructed access to the working space, since the only supports needed along the front of the table are the corner legs. This also facilitates cleaning of floors.

CPT 3032 control & packing table with two shelves for clean area

Size (LxWxH): 2000x1500x900 mm
This table is specially designed for sorting, inspection, functional control and packing of various sets for wards, clinics etc. and for surgical instrument sets in trays. The work could be done comfortably, either sitting or standing.
The worktop is made of a robust wood-based core material, surfaced with plastic laminate in a soft beige colour that reduces reflection of light from the surface. All edges is smooth. The extended width of the worktop is designed to facilitate thorough inspection of instrument trays and allow the use of large wrapping material.
The rigid frame is made of stainless steel (304).
There is unobstructed access to the working space, since the only supports needed along the front of the table are the corner legs. This also facilitates cleaning of floors.
It has double workspace. One workplace table is 700 mm wide worktop and other workplace is1400 mm worktop.
The table includes a two-shelf console, mounted on the worktop, for storage of packaging Materials. The rigid supporting columns of the console include 3 electrical outlets.
There is a free space of 450 mm between the lower shelf and the worktop, and 150 mm between the two shelves.
The table has a drawer unit (both sides as double model) mounted under the worktop.
Each drawer unit should be 400 mm wide and includes a drawer and a sliding plate.
Fluorescent tube fittings (Inspection lamp) is available. (Optional)

LFT 3089 linen fold table for clean area

Size (LxWxH) : 2000x1400x900 mm
The table is specially designed for sorting, inspection (each piece of linen can be moved over an illuminated inspection panel) and folding of surgical dressing sets and individually packaged towels/- gowns. The extended width also facilitates work with large dressing sheets. Work can be carried out comfortably, either sitting or standing.
Worktop is made of stainless steel SS 304 Grade with thickness 1.2mm, mat finished.
All edges of the worktop is smooth.
The top a built-in opalescent (milky) plastic surface plate, 1000 x 600 mm, illuminated from underneath by two 25 W fluorescent tubes located beneath the top in a laminated recess.
The table have two electrical outlets (one on each side).
The rigid frame is made of stainless steel (304).
There is unobstructed access to the working space, since the only supports needed along the front of the table are the corner legs. This also facilitates cleaning of floors.

WS3016 wire storage shelf module for dirty/disinfection area

Size (LxWxH) : 1500x450x1900 mm
Construction is based on single free-standing shelf modules for storage of clean linen, instruments, and packing material or sterilized goods, including disposables.
Moreover, two single modules can be placed back to back and combined as a double module unit.
The wire construction allows good air circulation while permitting easy inspection of the goods.
The wire shelves is made of special heavy-duty steel (304), chromium-plated and surface treated with clear epoxy varnish to facilitate cleaning.
The shelf unit is easy to assemble on site and all parts should fit precisely
Shelves are mounted by means of plastic clamps onto circular rigid posts, with the adjustable height within a range of about 50 mm. Each post include a height adjustable foot.
Each unit includes 5 shelves.
The shelf unit have optional Ø 125 mm castors for using as a mobile storage unit by replacing the foot with castors.

WS 3017 wire storage shelf module for clean supply area

Size (LxWxH) : 1525x455x1895 mm
Construction is based on single free-standing shelf modules for storage of clean linen, instruments, and packing material or sterilized goods, including disposables.
Moreover, two single modules can be placed back to back and combined as a double module unit.
The wire construction allow good air circulation while permitting easy inspection of the goods.
The wire shelves are made of special heavy-duty steel (304), chromium-plated and surface treated with clear epoxy varnish to facilitate cleaning.
The shelf unit is easy to assemble on site and all parts should fit precisely.
Shelves are mounted by means of plastic clamps onto circular rigid posts, with the adjustable height within a range of about 50 mm. Each post include a height adjustable foot.
Each unit include 5 shelves.
The shelf unit have optional Ø 125 mm castors for using as a mobile storage unit by replacing the foot with castors.

WS 3019 wire storage shelf module for sterile store

Size (LxWxH) : 1525x455x1895 mm
Construction is based on single free-standing shelf modules for storage of clean linen, instruments, and packing material or sterilized goods, including disposables.
Moreover, two single modules can be placed back to back and combined as a double module unit.
The wire construction allow good air circulation while permitting easy inspection of the goods.
The wire shelves are made of special heavy-duty steel (304), chromium-plated and surface treated with clear epoxy varnish to facilitate cleaning.
The shelf unit is easy to assemble on site and all parts should fit precisely.
Shelves are mounted by means of plastic clamps onto circular rigid posts, with the adjustable height within a range of about 50 mm. Each post include a height adjustable foot.
Each unit include 5 shelves.
The shelf unit have optional Ø 125 mm castors for using as a mobile storage unit by replacing the foot with castors.

FS 3079 free standing basket rack (15 Baskets) for Sterile store

Size (LxWxH) : 1850x480x2150 mm(Single), 1850x800x2150 mm(Double)
Single and double basket storage racks to store wire baskets in sterile storage and/or as pre-storage of clean packed goods.
The rack is designed as an open unit to promote aeration of sterilized goods and to make inspection of stored goods as easy as possible.
It provide rigid, horizontal guide-rails, consisting of 50 x 20 mm steel profiles for loading and unloading the baskets by sliding the baskets on rail.
The guide-rails is welded to a robust support column mounted on a rigid floor stand.
The columns is joined by support frames on top and below the base of the rack.
To facilitate cleaning of the floor, the base have a rigid construction that minimizes the number of legs needed for support.
Each leg have an adjustable foot (± 25 mm).
The rack is made of SS.
The single rack is a free-standing section that holds 5 baskets in each vertical.

PB -3065 Pass Box

Area : Dirty to Clean supply, ETO to Sterile supply & Sterile Issue
Size : 600x600x600mm, internal
It made up of SS 304 sheets with double wall construction
It has UV lights for safe storage of components
UV light have automatically switch off when any one door is opened
Pass-through chamber is based on electrical sliding hatches and fit all types of standard racks.
The chamber consist of two electrically operated sliding hatches.
Each hatch have its own 24 DC motor that powers a drive belt and ensures smooth operation, as well as its own convenient push-button control to ensure that both hatches cannot be opened at the same time.
The control should feature two modes of operation to open or close the hatch with a press button mechanism.
It has door interlocking to prevent simultaneous opening of both the doors
It has toughened glass paneling for easy visibility.

SSP 3047 stainless steel paneling for sterilizer & washer disinfector

All the sterilizers and washer disinfector should be recessed between the S.S. 304 quality panels.
The S.S. sheets have 18 gauge thicknesses with superior finish to match it with equipment finish.
The sheets are mounted on painted M.S. frame structure with adequate supports.
The panels have the doors for service access from loading side
There should not be any gaps between panel & the equipment

CTT 3089 closed transport trolley from sterile store to OT

Size : 1400x750x1260 mm(LxWxH) (External)
A Closed Transport trolley is used for sterile goods handling, for which higher protection than normal dust protection is required, e.g. short transports between hospital buildings. Suitable for handling baskets or containers with a total capacity of 9 STU (1 STU = 600 x 300 x 300 mm) on three solid, removable shelves (3 x 3 STU).
Trolley is fitted with large stainless steel wheels (Ø 160 mm) for easier maneuverability
It has two fixed and two swivel wheels with brakes.
It is fully welded stainless steel construction (minimum 18 gauges, 304).
The doors is open 270° for easy access and cleaning.
Trolley have lockable doors and include handlebars.

LD-3116 linen distribution & storage trolley

Size : 1020x740x1750 mm
Distribution trolleys are ergonomically designed for convenient manual distribution of sterilized goods to the users or for returning used goods to the central processing area.
The trolley is flexible and easy to handle and transport modular wire baskets and/or closed tote boxes, to increase handling efficiency and improve safety for the end-user, transport staff and the surroundings.
These trolleys have horizontally mounted slide bars that act as supports for the baskets and/or tote boxes.
A heavy-duty stainless steel (304) bottom plate should protect the goods during transport.
A sturdy handle is mounted on the bottom frame for convenient handling, even in narrow corridors.
The handle is so designed to permit the use of disposable plastic or reusable cloth covers for further protection during distribution.
The trolley is made of heavy-duty polished stainless steel (304) and every detail is designed for easy cleaning and disinfection.
The wheels (2 fixed, 2 swivel) have a diameter of 125 mm and are made of rubber with ball bearings.

TT-3210 table trolley for Dirty/Clean/Sterile area

Size : 1080x550x800 mm
The table trolley is made of all-welded medical grade stainless steel tubing.
The trolley have handlebars.
The solid top and bottom shelves are made of heavy gauge stainless steel (304) with a ground and polished finish, and with a 12 mm raised edge all around.
The lower shelf is 300 mm above floor level. There are protective buffer rollers on all four corners.
The table trolley has 4 swivel wheels, mounted in ball bearings, for easy handling even in narrow passages.

ITB-3672 Instrument Tray Big

Area : Various movement
Size : 450x250x70 mm
It is modular design with high precision and is designed for use with modular wire baskets through all phases of instrument processing: washing and disinfection (both manual and in an automatic washer-disinfector), ultrasonic cleaning, inspection and packing, sterilization, storage, distribution and usage.
It is self-drying after disinfection in hot water (min.+85°C)
Instrument trays are sturdy, jig-welded trays maintain their size and shape even if handled carelessly.
It is stackable.
The tray is made of stainless steel (304) wire net, with a maximum mesh size of 6.5 mm and a wire diameter of 1.5 mm. This design gives optimal cleaning results and at the same time prevents instruments from penetrating the sides of the tray.
All cross-points in the network and vertical wires to top and bottom frames is point welded.
All free wire ends are soft-polished to prevent injury when handled.
The bottom wire construction include a rigid, 3 mm diameter, stainless steel (304) wireframe to provide space for airing between goods and work surface and to allow use on roller, belt and chain conveyors.
It is electro-polished for smooth, clean surfaces and also suitable for ISO modular wire baskets

ITS 3459 Instrument tray small

Area : Various movement
Size : 340x250x70 mm
It is modular design with high precision and should be designed for use with modular wire baskets through all phases of instrument processing: washing and disinfection (both manual and in an automatic washer-disinfector), ultrasonic cleaning, inspection and packing, sterilization, storage, distribution and usage.
It is self-drying after disinfection in hot water (min.+85°C)
Instrument trays should be sturdy, jig-welded trays maintain their size and shape even if handled carelessly.
It is stackable.
The tray is made of stainless steel (304) wire net, with a maximum mesh size of 6.5 mm and a wire diameter of 1.5 mm. This design gives optimal cleaning results and at the same time prevents instruments from penetrating the sides of the tray
All cross-points in the network and vertical wires to top and bottom frames should be point welded.
All free wire ends are soft-polished to prevent injury when handled.
The bottom wire construction include a rigid, 3 mm diameter, stainless steel (304) wire frame to provide space for airing between goods and work surface and to allow use on roller, belt and chain conveyors.
It is electro-polished for smooth, clean surfaces and also suitable for modular wire baskets.

MSB-3115 modular sterilizing baskets big

Size : 585x395x195 mm
Area : Various movement
It is modular design with standard SPRI sizes and high precision and is designed for sterilizing / processing as well as easy handling and management of the supply, storage and distribution of re-circulated sterilized goods.
It is self-drying after disinfection in hot water (min.+85°C)
It is sturdy, jig-welded trays maintain their size and shape even if handled carelessly.
It is both nest able and stackable There should be special wire support to help making baskets both stackable (when the supports are folded into the basket) and nest able (when the supports are folded out)
The top frame is designed such that it serve as a handle grip for easy carrying even when heavily loaded.
There is be no sharp edges or wires.
The surfaces is smooth to assure easy cleaning in a washer-disinfector.
The baskets is made of electro-polishes heavy-duty stainless steel (304) and have a rigid bottom frame that gives space for airing between goods and work surfaces and allow use on roller belt and chain conveyors.
It is designed and manufactured in accordance with high quality specifications to assure long lifetime.

MSB 3116 modular sterilizing baskets medium

Size : 585x395x100 mm
Area : Various movement
It is modular design with standard SPRI sizes and high precision and is designed for sterilizing / processing as well as easy handling and management of the supply, storage and distribution of re-circulated sterilized goods.
It is self-drying after disinfection in hot water (min.+85°C)
It is sturdy, jig-welded trays maintain their size and shape even if handled carelessly
It is both nest able and stackable There is special wire support to help making baskets both stackable (when the supports are folded into the basket) and nest able (when the supports are folded out)
The top frame is designed such that it serve as a handle grip for easy carrying even when heavily loaded.
There is no sharp edges or wires.
The surfaces are smooth to assure easy cleaning in a washer-disinfector.
The baskets are made of electro-polishes heavy-duty stainless steel (304) and have a rigid bottom frame that gives space for airing between goods and work surfaces and allow use on roller belt and chain conveyors.
It is designed and manufactured in accordance with high quality specifications to assure long lifetime.

SC -3764 staff chair

Medium Back chair
Rest on high quality 50mm castors on4 legs with cross reinforcement for sides with arm rest and foot stumps of PVC
Have seamlessly upholstered seat and backrest, washable antimicrobial with poly foam cushion.
Colour of base is black.
Height adjustable, broad, padded.
Upholstered arm rests and comfortable back rest.